On the variety of triangles for a hyper-Kähler fourfold constructed by Debarre and Voisin

We study the similarities between the Fano varieties of lines on a cubic fourfold, a hyper-Kähler fourfold studied by Beauville and Donagi, and the hyper-Kähler fourfold constructed by Debarre and Voisin in [3]. We exhibit an analog of the notion of “triangle” for these varieties and prove that the 6-dimensional variety of “triangles” is a Lagrangian subvariety in the cube of the constructed hyper-Kähler fourfold.     

Dynamic and buckling analysis of polymer hybrid composite beam with variable thickness

This work deals with a study of the dynamic and buckling analysis of polymer hybrid composite(PHC) beam. The beam has variable thickness and is reinforced by carbon nanotubes(CNTs) and nanoclay(NC) simultaneously. The governing equations are derived based on the first shear deformation theory(FSDT). A three-phase HalpinTsai approach is used to predict the mechanical properties of the PHC. We focus our attention on the effect of the simultaneous addition of NC and CNT on the vibration and buckling analysis of the PHC beam with variable thickness. Also a comparison study is done on the sensation of three impressive parameters including CNT, NC weight fractions, and the shape factor of fillers on the mechanical properties of PHC beams,as well as fundamental frequencies of free vibrations and critical buckling load. The results show that the increase of shape factor value, NC, and CNT weight fractions leads to considerable reinforcement in mechanical properties as well as increase of the dimensionless fundamental frequency and buckling load. The variation of CNT weight fraction on elastic modulus is more sensitive rather than shear modulus but the effect of NC weight fraction on elastic and shear moduli is fairly the same. The shape factor values more than the medium level do not affect the mechanical properties.     

无轴承旋翼柔性梁载荷特性研究

应用Hamilton原理建立了双路传力的无轴承旋翼运动方程。采用均匀入流模型,基于直升机飞行平衡条件,建立了无轴承旋翼柔性梁载荷的计算模型,并通过算例验证了模型的精度。利用该模型,研究了全机重心位置、机身气动阻力以及平尾安装角对柔性梁载荷特性的影响,给出了各因素对柔性梁载荷的影响趋势,得出了降低柔性梁载荷的方法。数值结果表明:2cm左右重心位置的变化能够引起9%~11%的柔性梁载荷变化量,15%气动阻力的增加会导致约9%的柔性梁载荷的增大;2°平尾安装角的变化引起约10%柔性梁载荷的变化量,3°平尾安装角的变化引起约26%柔性梁载荷的变化。     

有耗介质层上多导体传输线的电磁耦合时域分析方法

目前,针对空间电磁场作用有耗介质层上传输线的电磁耦合,仍缺乏有效的数值分析方法.因此,本文提出一种高效的时域混合算法,很好地解决了有耗介质层上传输线电磁耦合建模难的问题.首先,对经典传输线方程进行改进,推导了适用于有耗介质层上多导体传输线电磁耦合分析的修正传输线方程.然后,结合时域有限差分方法和相应插值技术,求解修正传输线方程,获得多导线及其端接负载上的电压和电流响应,并实现空间电磁场辐射与多导线瞬态响应的同步计算.最后,通过相应计算实例的数值模拟,与CST软件的仿真结果进行对比,验证了时域混合算法的正确性和高效性.     

A new Monte Carlo model for predicting the mechanical properties of fiber yarns

Understanding the complicated failure mechanisms of hierarchical composites such as fiber yarns is essential for advanced materials design. In this study, we developed a new Monte Carlo model for predicting the mechanical properties of fiber yarns that includes statistical variation in fiber strength. Furthermore, a statistical shear load transfer law based on the shear lag analysis was derived and implemented to simulate the interactions between adjacent fibers and provide a more accurate tensile stress distribution along the overlap distance. Simulations on two types of yarns, made from different raw materials and based on distinct processing approaches, predict yarn strength values that compare favorably with experimental measurements. Furthermore, the model identified very distinct dominant failure mechanisms for the two materials, providing important insights into design features that can improve yarn strength.     

ZnO nanowire lines and bundles: Template-deformation-guided alignment for patterned field-electron emitters

One-dimensional ZnO materials have been promising for field-emission (FE) application, but how to facially control the alignment of ZnO emitters is still a great challenge especially for patterned display application. Here, we report the fabrication of novel ZnO nanowire (NW) line and bundle arrays for patterned field-electron emitters. The effects of PS template size and heating time on the resulted ZnO nanoarrays were systematically studied. The deformation degree of PS templates was controlled and hence utilized to adjust the alignment of electrochemically deposited ZnO arrays. It was found that the length of NW lines and the density of NW bundles can effectively tuned by the PS template heating time. The optimal FE performance with turn-on electric field as low as of 4.4 V μm⁻¹ and the field-enhancement factor as high as of 1450 were achieved through decreasing the screening effect among the patterned field-electron emitters.     

Structural response of stiffened plates in similitude under a turbulent boundary layer excitation

In structural dynamics, similitude laws usually deal with simple configurations as thin flat plates with point forces. Only recently, few papers have analyzed stiffened shells or stochastic pressure loads.This research activity extends the applicability of some similitude laws, developed for thin flat plates under a turbulent boundary layer load, to ribbed plates forced by the same wall pressure fluctuations.The work addresses the problem of designing a scaled experimental test-article and, successively, of re-modulating the measured data in order to get the structural response of an original (unscaled) configuration.Due to the complexity of the structural domain, the design of a scaled configuration leads to a distorted similitude. Then, a simple approach, to circumvent the distortion effects, is proposed.     

面向装配节点平衡的产品生产物流协调优化研究

在由多个并行零件生产线和装配线组成的产品生产物流中, 各生产线的瓶颈工序制约了装配节点及其整个生产物流的平衡. 为此, 基于约束理论和JIT(Just In Time)思想, 提出主、次瓶颈的概念及其判别方法和主瓶颈拉动次瓶颈、瓶颈前后拉动生产与平行顺序移动生产相结合的生产策略, 研究了基于负荷率的瓶颈工序负荷控制方法和主瓶颈触发次瓶颈拉式生产的时间控制方法, 使瓶颈工序利用率最大化, 各个零件到达装配节点的同步性得到改善. 算例的SIMIO仿真结果表明, 装配节点的在制品存量大幅度减少, 利用率提高.